WLAP repeater mode is WDS repeater, so it can connect other wireless device with MAC address. So you can set another station in Bridge mode. AirLive WLAP, WLAP is in conformity with. In accordance with 93/68/ EEC Directive and /5 EC-R & TTE Directive. Clause. Description. The WLAP and WLAP uses different firmwares. Please do not use the wrong firmware (i.e. do not use WLAP firmware on.
|Published (Last):||25 November 2011|
|PDF File Size:||16.3 Mb|
|ePub File Size:||13.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
Airlive / Ovislink WL-5450AP
An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network. Comments to this Manuals Your Name. Users can use this feature to build up a large wireless network in a large space like airports, hotels and schools …etc. Press Refresh to get the latest information. Apply Changes Press to save the new settings on the screen. You can share files and printers between wireless stations PC and laptop with wireless network adapter installed.
Other Other Upgrade Firmware 1.
Advanced Settings Advanced Settings It is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance Authentication Type To provide a certain level of security, the IEEE Status In this screen, you can see the current settings and status of this Access Point.
Remember your user name and password for you will be asked to enter them every time you access the web server of this Access Point. To print the manual completely, please, download it. Performing the Factory Reset will erase all previously entered device settings. Infinite loop will happen in the network when WDS is enabled and there are multiple active paths between stations.
Preauthentication provides a way to establish a PMK security association before a client associates.
Download AirLive WLAP Access Point Firmware eu for OS Independent
Firmware Version The current version of the firmware installed in this device. Refer to the illustration below. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
System manager can use the system log to trace when problems occur. Connect an Ethernet cable between your computer and the Wireless Access Point.
Please note that by using any encryption, by which data packet is encrypted before transmission to prevent data packets from being eavesdropped by unrelated people, there may be a significant degradation of the data throughput on the wireless link.
This manual also for: These limits are designed to provide reasonable protection against harmful interference in a residential installation. Before you starting hardware connection, you are advised to find an appropriate location to place the Access Point. Parts Names and Functions 1. When you are in the client mode, you can select one AP to associate. Wireless Basic Settings This page includes all primary and major parameters. Security Security Here you can configure the security of your wireless network.
You may enter up to 20 characters as a remark to the previous MAC Address. Leaving the user name airlivve password blank will disable the protection. If the list contains no entries with this airllive being enabled, then no clients will be able to access this Access Point. Page 26 change automatically. Don’t show me this message again. Table Of Contents Introduction Channel Number The number of channels supported depends on the region of this Access Point.
In the Address box, enter the following: The default is seconds. Make sure your wired station is set to the same subnet as the Wireless Access Point, i. System System Uptime The time period since the device was up. Enter aorlive from picture: Also, remember to adjust the antenna; usually the higher the antenna is placed, the better will be the performance.
The login screen prompts immediately airllive you finish setting the account and password. All stations communicating with the Access Point must use the same channel.
Table of Contents Add to my manuals Add.
Page 33 Save Settings to File: Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point.
Security Here you can configure the security of your wireless network.
Client Mode ad-hoc Client Mode Ad-hoc If set to the Client Ad-hoc mode, this device can work like a wireless station when it is connected to a computer so that the computer can send packets from wired end to wireless interface.