HONEYWELL OP10 PDF

Model Series OP10/20/30/40/45/ K Rev. 9, Sep WHAT IS THE Honeywell OmniProx™ READER? The OmniProx Reader is an RFID proximity. : Honeywell Access OP10HON OmniProx Mini-Mullion Proximity Reader: Security And Surveillance Accessories: Camera & Photo. Find great deals for Honeywell OP10 OmniProx Proximity Card Reader Control. Shop with confidence on eBay!.

Author: Akinojora Dimuro
Country: Finland
Language: English (Spanish)
Genre: Automotive
Published (Last): 27 November 2010
Pages: 490
PDF File Size: 10.22 Mb
ePub File Size: 6.58 Mb
ISBN: 867-7-87059-155-4
Downloads: 91699
Price: Free* [*Free Regsitration Required]
Uploader: Jujora

These installation instructions contain the following information: To connect the reader to the host, perform the following steps: If there is a connector on the end of the cable used during manufacture for testing purposescut it off. Splice the reader pigtail wires to honeyweell corresponding host wires and cover each connection see Figure 2.

Honeywell Op10 OmniProx HID Proximity Card Readers 16vdc Weigand

If the tamper output is being utilized, connect the purple wire to the correct input on the host. Trim and cover all conductors that are not used. Hides mounting screws and protects the reader The model OP90 uses a security screw on the bottom of the reader to secure the cover. Remove this security screw using the supplied tool. Then slide the back plate down slightly and then lift it up from the bottom. Select the desired mounting holes and drill them out.

Figure 2 Wiring Notes: Mount the reader with the appropriate screws not supplied as indicated on the template.

To surface mount the reader, perform the following: Determine an appropriate mounting position for the reader.

Peel off the back of the self-stick mounting label template included with the unit and place at the desired mounting position. Additional templates can be downloaded from www. Using the template as a guide, drill two holes hole size is indicated on mounting template for mounting the reader to the surface.

If mounting on metal, place a grommet or electrical tape around the edge of the hole. A linear type power supply is recommended. The individual wires coming out of the reader are color coded according to the recommended Wiegand standard. If either 5 or 12 volts are available, use 12 volts for better performance.

  GEORGE BURDEAU PDF

When using a separate power supply for the reader, the reader, power supply and host must have a common ground. The recommended cable depends on the distance from the reader to the host.

See Table 1 on the next page for the correct wire gage based upon distance. Larger wire gauges are acceptable. The wire must be stranded with an overall shield, either foil or braided. If the tamper is not being used, 5 conductor cable is required; otherwise 6 conductor cable is required. The cable shield wire on the reader should be attached to an Earth ground best or signal ground connection at the panel or power supply end of the cable.

This configuration is homeywell for shielding the reader cable from external interference. Linear type Recommended Operating Voltage Range: Recommended cable is only a guideline, use any manufacturer that meets the gage and shield specifications. Do honeyeell by performing the following steps: Tamper Output Open collector, active low, max.

The LED and beeper will activate three times. This indicates that the reader is working properly. Maximum Cable Distance to Host: See Table 2 for the honeywel, card type based on the reader model. The LED will momentarily flash green and a short beep will be emitted.

This indicates that the card hojeywell read properly by OmniProx.

Honeywell OP10 Proximity Mullion Reader – HID Compatible | Pro Safety Systems

See Table 2 Regulatory Approvals: The FCC requires the following statement for your information: This equipment op1 and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.

It has been type hoenywell and found to comply with the limits for a Class B computing device in accordance with the specifications in Pp10 15 of FCC Rules, which are designed to provide ip10 protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: The user or master may find the following booklet prepared by the Federal Communications Commission helpful: The user shall not make any changes or modifications to the equipment unless pp10 by the Installation Instructions or User’s Manual.

  AAIA FACTBOOK 2015 PDF

Unauthorized changes or modifications could void the ohneywell authority to operate the equipment. Immunity requirements for components of fire, intruder and social alarm systems Issued by: OmniProx is a registered trademark of Honeywell International. Wiegand is a licensed trademark of HID Corp.

Seller’s obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance with Seller’s specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service.

Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent hpneywell personal injury or property loss by burglary, robbery, fire or otherwise; or that the products will in all cases provide adequate warning or protection.

Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. However, if Seller is held liable, whether directly or indirectly, for any loss or damage arising under this Limited Warranty or otherwise, regardless of cause or origin, Seller’s maximum liability shall not in any case exceed the purchase price of the product, which shall be the complete and exclusive remedy against Seller.

This warranty replaces any previous warranties and is the only warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized. It’s a community-based project which helps to repair anything.