LA3600 DATASHEET PDF

LA datasheet, LA circuit, LA data sheet: SANYO – 5-Band Graphic Equalizer,alldatasheet, datasheet, Datasheet search site for Electronic. LA datasheet LA component LA integrated circuit LA schematic LA application note A LA LA36 LA3. Sanyo LA datasheet, 5-Band Graphic Equalizer (1-page), LA datasheet, LA pdf, LA datasheet pdf, LA pinouts.

Author: Fer Zulujar
Country: Iraq
Language: English (Spanish)
Genre: Education
Published (Last): 27 July 2007
Pages: 181
PDF File Size: 13.88 Mb
ePub File Size: 9.3 Mb
ISBN: 508-5-72603-116-8
Downloads: 44128
Price: Free* [*Free Regsitration Required]
Uploader: Kilabar

This will hold good only when following are carried out. Hi Eric Nice question. The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads.

Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5. Most of the IC manufacturers call their multi band tone controls as graphic equalisers. I used 9V DC for powering the circuit. Previous post Next post.

LA datasheet & applicatoin notes – Datasheet Archive

Hi Eric Nice question. You may also like: How we connect stereo input to this circuit? Could i add this to my homemade tube amp, datashet take out the LA?

C12 is the output capacitor and resistor R6 limits the supply current. You may also like: Assemble the circuit on a good quality PCB. Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response.

  LOCKHEED CONSTELLATION MOTORBOOKS PDF

Leave a Reply Cancel reply Your email address will not be published. This will hold good only when following are carried out.

I used 9V DC for powering the circuit. Could i add this to my homemade tube amp, and take out the LA? Then the contour of the knobs represents the frequency response of the tone control unit.

Datasheet «LA3600»

Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5. The power supply must be well regulated and noise free. The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads. Your email address will not be published.

Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. How we connect stereo input to this circuit? LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc. If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost.

  GORKAMORKA GUBBINZ PDF

LA3600 datasheet download

Your email address will not be published. If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 la33600 R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost.

Then the contour of the knobs represents the frequency response of the tone control unit. The power supply must be well regulated and noise free. Assemble the circuit on a good quality PCB. Most of the IC manufacturers datasheft their multi band tone controls as graphic equalisers.

In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands.

Leave a Reply Cancel reply Your email address will not be published.

LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc. Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. Previous post Next post.