Default Password, Login and IP for your Comtrend CT+ router. User Manuals and How to Factory Reset your Comtrend CT+ router. To perform a Comtrend router Login or Reset, follow these instructions. Router The Comtrend CT+ router with 54mbps WiFi, 4 mbps ETH-ports. This manual provides information related to the installation, operation, and application support for immediate service by email at [email protected] com.
|Published (Last):||14 June 2015|
|PDF File Size:||4.80 Mb|
|ePub File Size:||12.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
The information and messages contained herein are proprietary to Comtrend Corporation. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written permission by Comtrend Corporation. The router is powered down. Green An Ethernet Link is established. Chapter 2 Installation Hardware Installation In the rear panel, there is a reset button. To load the factory default settings, hold the reset button down for at least 5 seconds.
Reset button Follow the instructions below to complete the hardware connections. Connection to Power Connect the Power jack to the shipped power cord. Attach the power adapter to the wall outlet or other AC source. After all connections have been made, turn the power-switch to the on position.
After power on, the router performs a self-test. Wait for a few seconds until the test is finished, then the router will be ready to operate. When the screen displays as below, click the Next button. When the screen displays as below, select Search for a suitable driver and click the Next button. Select Specify a location and click the Next button.
If you are installing the software from a disk, insert the disk. Select the location of the file using the Browse button. Locate the file, and click the Open button. When the screen displays as below, click the OK button. When the screen below displays, click the NEXT button. Click the Finish button, when the screen displays as below. Chapter 3 Login via the Web Browser This section describes how to manage the router via a Web browser via the remote end.
The Web page is best viewed with Microsoft Internet Explorer 5. A unique default user account is assigned with user name root and password To log on to the system from the Web browser, follow the steps below: Start your Internet browser. Type the IP address for the router in the Web address field. It will then read the configuration profile from the Permanent Storage section on the flash memory.
The default attributes are overridden when identical attributes with different values are configured. The configuration profile in Permanent Storage can be created via the Web user interface, the console, or telnet user interface, or other management protocols.
The selections available on the left side of menu are based upon the configured connection. All statistics screens are updated every 15 seconds.
The Reset button resets the statistics. You can either manually customize the router or follow the online instruction to set up the router. Up to eight PVC profiles can be configured and saved on the flash memory.
To activate a particular PVC profile, you need to navigate all the Quick Setup pages until the last summary page, then click on the Finish button and reboot the system. Un-tick this checkbox to enable manual setup and display the following screen.
Select Enable Quality Of Service if required. Then, choose the Encapsulation mode.
Click Next to display the following screen. Choosing different connection types pops up different settings requests. The following screen appears: Unless your service provider specially requires this setup, do not select it. If selected, enter your static IP address. The following screen will be displayed.
Comtrend Corporation CT-5374 User Manual
To enable the wireless function, select the box manuzl clicking on it and input the SSID. Click Back if you wish to modify the settings.
The Web UI will not respond until the system is brought up again. Select Quick Setup and click Next. The following screen appears. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related manal after the system comes up. Upon completion, click Next. After entering your settings, select Next to display the following screen. To configure Bridging, do the following.
Chapter 6 Advanced Setup This chapter explains: Save button only saves the LAN configuration data. Enter the subnet mask for the LAN port.
Easiest Way to Forward Ports on the Comtrend CT-536 Router
Select a Service User should select the mwnual from the list. Custom Server User can enter the name of their choice. Select an Application User should select the application from the list. Or Custom Application Or User can enter the name of their choice. Trigger Port Start Ct5536 the starting trigger port number when you select custom application. When an application is selected the port ranges are automatically configured.
All of the specified conditions in this filter rule must be satisfied for the rule to comtremd effect. Filter Name Type a name for the filter rule. Protocol User can select from: Source Subnet Mask Enter source subnet mask. Source Port port or port: The default setting for Incoming is Accepted. To add a filtering rule, simply click the Add button. To configure the parameters, please reference Outgoing table above.
To add a parental control, simply click the Add button. Name of the Filter. Set the MAC address to access the Internet. Set which days that will have block restrictions to Internet access. Choose Add to configure network traffic classes. The following screen will be displayed The screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header TOS byte.
COMTREND CORPORATION CT USER MANUAL Pdf Download.
A rule consists of a class name and at least one condition below. All of the specified conditions in this classification rule must be satisfied for the rule to take effect. Source Port port or Enter source port number. The Static Route screen lists the configured static routes, and allows configuring static routes.
Choose Add or Remove to configure the static routes. To add static route, click the Add button to display the following screen.
To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the ‘Enabled’ checkbox for the interface.
To add a dynamic DNS service, simply click the Add button. Password Enter the password for the dynamic DNS server. The DSL Settings dialog box allows you to select an appropriate modulation mode. Dmt if you want the system to use G. Lite Enabled Sets G. Lite if you want the system to use G. Each group will perform as an independent network. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group.
To create a group from the list, first enter the group name and then select from the available interfaces on the list. Chapter 7 Wireless The Wireless dialog box allows you to enable the wireless capability, hide the access point, set the wireless network name and restrict the channel set.
You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name also known as SSID and restrict the channel set based on country requirements. The default is Enable Wireless. WEP is a set of security services used to protect